Header logo is


2015


Experimental investigation of optimal adhesion of mushroomlike elastomer microfibrillar adhesives
Experimental investigation of optimal adhesion of mushroomlike elastomer microfibrillar adhesives

Marvi, H., Song, S., Sitti, M.

Langmuir, 31(37):10119-10124, American Chemical Society, August 2015 (article)

Abstract
Optimal fiber designs for the maximal pull-off force have been indispensable for increasing the attachment performance of recently introduced gecko-inspired reversible micro/nanofibrillar adhesives. There are several theoretical studies on such optimal designs; however, due to the lack of three-dimensional (3D) fabrication techniques that can fabricate such optimal designs in 3D, there have not been many experimental investigations on this challenge. In this study, we benefitted from recent advances in two-photon lithography techniques to fabricate mushroomlike polyurethane elastomer fibers with different aspect ratios of tip to stalk diameter (β) and tip wedge angles (θ) to investigate the effect of these two parameters on the pull-off force. We found similar trends to those predicted theoretically. We found that β has an impact on the slope of the force-displacement curve while both β and θ play a role in the stress distribution and crack propagation. We found that these effects are coupled and the optimal set of parameters also depends on the fiber material. This is the first experimental verification of such optimal designs proposed for mushroomlike microfibers. This experimental approach could be used to evaluate a wide range of complex microstructured adhesive designs suggested in the literature and optimize them.

pi

DOI [BibTex]

2015


DOI [BibTex]


pH-taxis of biohybrid microsystems
pH-taxis of biohybrid microsystems

Zhuang, J., Carlsen, R. W., Sitti, M.

Scientific reports, 5, Nature Publishing Group, June 2015 (article)

Abstract
The last decade has seen an increasing number of studies developing bacteria and other cell-integrated biohybrid microsystems. However, the highly stochastic motion of these microsystems severely limits their potential use. Here, we present a method that exploits the pH sensing of flagellated bacteria to realize robust drift control of multi-bacteria propelled microrobots. Under three specifically configured pH gradients, we demonstrate that the microrobots exhibit both unidirectional and bidirectional pH-tactic behaviors, which are also observed in free-swimming bacteria. From trajectory analysis, we find that the swimming direction and speed biases are two major factors that contribute to their tactic drift motion. The motion analysis of microrobots also sheds light on the propulsion dynamics of the flagellated bacteria as bioactuators. It is expected that similar driving mechanisms are shared among pH-taxis, chemotaxis, and thermotaxis. By identifying the mechanism that drives the tactic behavior of bacteria-propelled microsystems, this study opens up an avenue towards improving the control of biohybrid microsystems. Furthermore, assuming that it is possible to tune the preferred pH of bioactuators by genetic engineering, these biohybrid microsystems could potentially be applied to sense the pH gradient induced by cancerous cells in stagnant fluids inside human body and realize targeted drug delivery.

pi

DOI Project Page [BibTex]

DOI Project Page [BibTex]


Structural optimization for flexure-based parallel mechanisms--Towards achieving optimal dynamic and stiffness properties
Structural optimization for flexure-based parallel mechanisms–Towards achieving optimal dynamic and stiffness properties

Lum, G. Z., Teo, T. J., Yeo, S. H., Yang, G., Sitti, M.

Precision Engineering, 42, pages: 195-207, Elsevier, May 2015 (article)

Abstract
Flexure-based parallel mechanisms (FPMs) are a type of compliant mechanisms that consist of a rigid end-effector that is articulated by several parallel, flexible limbs (a.k.a. sub-chains). Existing design methods can enhance the FPMs’ dynamic and stiffness properties by conducting a size optimization on their sub-chains. A similar optimization process, however, was not performed for their sub-chains’ topology, and this may severely limit the benefits of a size optimization. Thus, this paper proposes to use a structural optimization approach to synthesize and optimize the topology, shape and size of the FPMs’ sub-chains. The benefits of this approach are demonstrated via the design and development of a planar X − Y − θz FPM. A prototype of this FPM was evaluated experimentally to have a large workspace of 1.2 mm × 1.2 mm × 6°, a fundamental natural frequency of 102 Hz, and stiffness ratios that are greater than 120. The achieved properties show significant improvement over existing 3-degrees-of-freedom compliant mechanisms that can deflect more than 0.5 mm and 0.5°. These compliant mechanisms typically have stiffness ratios that are less than 60 and a fundamental natural frequency that is less than 45 Hz.

pi

DOI [BibTex]

DOI [BibTex]


Controlled surface topography regulates collective 3D migration by epithelial--mesenchymal composite embryonic tissues
Controlled surface topography regulates collective 3D migration by epithelial–mesenchymal composite embryonic tissues

Song, J., Shawky, J. H., Kim, Y., Hazar, M., LeDuc, P. R., Sitti, M., Davidson, L. A.

Biomaterials, 58, pages: 1-9, Elsevier, April 2015 (article)

Abstract
Cells in tissues encounter a range of physical cues as they migrate. Probing single cell and collective migratory responses to physically defined three-dimensional (3D) microenvironments and the factors that modulate those responses are critical to understanding how tissue migration is regulated during development, regeneration, and cancer. One key physical factor that regulates cell migration is topography. Most studies on surface topography and cell mechanics have been carried out with single migratory cells, yet little is known about the spreading and motility response of 3D complex multi-cellular tissues to topographical cues. Here, we examine the response to complex topographical cues of microsurgically isolated tissue explants composed of epithelial and mesenchymal cell layers from naturally 3D organized embryos of the aquatic frog Xenopus laevis. We control topography using fabricated micropost arrays (MPAs) and investigate the collective 3D migration of these multi-cellular systems in these MPAs. We find that the topography regulates both collective and individual cell migration and that dense MPAs reduce but do not eliminate tissue spreading. By modulating cell size through the cell cycle inhibitor Mitomycin C or the spacing of the MPAs we uncover how 3D topographical cues disrupt collective cell migration. We find surface topography can direct both single cell motility and tissue spreading, altering tissue-scale processes that enable efficient conversion of single cell motility into collective movement.

pi

DOI [BibTex]

DOI [BibTex]


Transfer Printing of Metallic Microstructures on Adhesion-Promoting Hydrogel Substrates
Transfer Printing of Metallic Microstructures on Adhesion-Promoting Hydrogel Substrates

Wu, H., Sariola, V., Zhu, C., Zhao, J., Sitti, M., Bettinger, C. J.

Advanced Materials, 27(22):3398-3404, April 2015 (article)

Abstract
Fabrication schemes that integrate inorganic microstructures with hydrogel substrates are essential for advancing flexible electronics. A transfer printing process that is made possible through the design and synthesis of adhesion-promoting hydrogels as target substrates is reported. This fabrication technique may advance ultracompliant electronics by melding microfabricated structures with swollen hydrogel substrates.

pi

DOI [BibTex]

DOI [BibTex]


Biomedical applications of untethered mobile milli/microrobots
Biomedical applications of untethered mobile milli/microrobots

Sitti, M., Ceylan, H., Hu, W., Giltinan, J., Turan, M., Yim, S., Diller, E.

Proceedings of the IEEE, 103(2):205-224, IEEE, March 2015 (article)

Abstract
Untethered robots miniaturized to the length scale of millimeter and below attract growing attention for the prospect of transforming many aspects of health care and bioengineering. As the robot size goes down to the order of a single cell, previously inaccessible body sites would become available for high-resolution in situ and in vivo manipulations. This unprecedented direct access would enable an extensive range of minimally invasive medical operations. Here, we provide a comprehensive review of the current advances in biomedical untethered mobile milli/microrobots. We put a special emphasis on the potential impacts of biomedical microrobots in the near future. Finally, we discuss the existing challenges and emerging concepts associated with designing such a miniaturized robot for operation inside a biological environment for biomedical applications.

pi

DOI [BibTex]

DOI [BibTex]


Collective 3D Migration of Embryonic Epithelial Mesenchymal Composite Tissues are Regulated by Surface Topology
Collective 3D Migration of Embryonic Epithelial Mesenchymal Composite Tissues are Regulated by Surface Topology

Song, J., Shawky, J., Kim, Y. T., Hazar, M., Sitti, M., LeDuc, P. R., Davidson, L. A.

Biophysical Journal, 108(2):455a, Elsevier, January 2015 (article)

Abstract
Cells in tissues encounter a range of physical cues as they migrate. Probing single cell and collective migratory responses to physically defined three-dimensional (3D) microenvironments and the factors that modulate those responses are critical to understanding how tissue migration is regulated during development, regeneration, and cancer. One key physical factor that regulates cell migration is topology. Most studies on surface topology and cell mechanics have been carried out with single migratory cells, yet little is known about the spreading and motility response of 3D complex multicellular tissues to topological cues. Here, we examine the behaviors of microsurgically isolated tissue explants composed of epithelial and mesenchymal cell layers from naturally 3D organized embryos of the aquatic frog Xenopus laevis to complex topological cues. We control topology using fabricated micropost arrays (MPAs) with different diameters (e.g., different spacing gaps) and investigate the collective 3D migration of these multicellular systems in these MPAs. Our topographical controlled approach for cellular application enables us to achieve a high degree of control over micropost positioning and geometry via simple, accurate, and repeatable microfabrication processes. We find that the topology regulates both collective and individual cell migration and that dense MPAs reduce but do not eliminate tissue spreading. By modulating cell size through the cell cycle inhibitor Mitomycin C or the spacing within MPAs we discover a role for topology in disrupting collective enhancement of cell migration. We find 3D topological cues can direct both single cell motility and tissue spreading, altering tissue-scale processes that enable efficient conversion of single cell motility into collective movement.

pi

DOI [BibTex]

DOI [BibTex]


Three-dimensional heterogeneous assembly of coded microgels using an untethered mobile microgripper
Three-dimensional heterogeneous assembly of coded microgels using an untethered mobile microgripper

Chung, S. E., Dong, X., Sitti, M.

Lab on a Chip, 15(7):1667-1676, Royal Society of Chemistry, January 2015 (article)

Abstract
Three-dimensional (3D) heterogeneous assembly of coded microgels in enclosed aquatic environments is demonstrated using a remotely actuated and controlled magnetic microgripper by a customized electromagnetic coil system. The microgripper uses different ‘stick–slip’ and ‘rolling’ locomotion in 2D and also levitation in 3D by magnetic gradient-based pulling force. This enables the microrobot to precisely manipulate each microgel by controlling its position and orientation in all x–y–z directions. Our microrobotic assembly method broke the barrier of limitation on the number of assembled microgel layers, because it enabled precise 3D levitation of the microgripper. We used the gripper to assemble microgels that had been coded with different colours and shapes onto prefabricated polymeric microposts. This eliminates the need for extra secondary cross-linking to fix the final construct. We demonstrated assembly of microgels on a single micropost up to ten layers. By increasing the number and changing the distribution of the posts, complex heterogeneous microsystems were possible to construct in 3D.

pi

DOI Project Page [BibTex]

DOI Project Page [BibTex]


Integrating mechanism synthesis and topological optimization technique for stiffness-oriented design of a three degrees-of-freedom flexure-based parallel mechanism
Integrating mechanism synthesis and topological optimization technique for stiffness-oriented design of a three degrees-of-freedom flexure-based parallel mechanism

Lum, G. Z., Teo, T. J., Yang, G., Yeo, S. H., Sitti, M.

Precision Engineering, 39, pages: 125-133, Elsevier, January 2015 (article)

Abstract
This paper introduces a new design approach to synthesize multiple degrees-of-freedom (DOF) flexure-based parallel mechanism (FPM). Termed as an integrated design approach, it is a systematic design methodology, which integrates both classical mechanism synthesis and modern topology optimization technique, to deliver an optimized multi-DOF FPM. This design approach is separated into two levels. At sub-chain level, a novel topology optimization technique, which uses the classical linkage mechanisms as DNA seeds, is used to synthesize the compliant joints or limbs. At configuration level, the optimal compliant joints are used to form the parallel limbs of the multi-DOF FPM and another stage of optimization was conducted to determine the optimal space distribution between these compliant joints so as to generate a multi-DOF FPM with optimized stiffness characteristic. In this paper, the design of a 3-DOF planar motion FPM was used to demonstrate the effectiveness and accuracy of this proposed design approach.

pi

DOI [BibTex]


Actively controlled fibrillar friction surfaces
Actively controlled fibrillar friction surfaces

Marvi, H, Han, Y, Sitti, M

Applied Physics Letters, 106(5):051602, AIP Publishing, January 2015 (article)

Abstract
In this letter, we propose a technique by which we can actively adjust frictional properties of elastic fibrillar structures in different directions. Using a mesh attached to a two degree-of-freedom linear stage, we controlled the active length and the tilt angle of fibers, independently. Thus, we were able to achieve desired levels of friction forces in different directions and significantly improve passive friction anisotropies observed in the same fiber arrays. The proposed technique would allow us to readily control the friction anisotropy and the friction magnitude of fibrillar structures in any planar direction.

pi

DOI [BibTex]

DOI [BibTex]


no image
The average number of distinct sites visited by a random walker on random graphs

De Bacco, C., Majumdar, S. N., Sollich, P.

Journal of Physics A: Mathematical and Theoretical, 48(20):205004, IOP Publishing, 2015 (article)

pio

Preprint link (url) [BibTex]

Preprint link (url) [BibTex]


no image
The edge-disjoint path problem on random graphs by message-passing

Altarelli, F., Braunstein, A., Dall’Asta, L., De Bacco, C., Franz, S.

PloS one, 10(12):e0145222, Public Library of Science, 2015 (article)

pio

Code Preprint link (url) Project Page [BibTex]

Code Preprint link (url) Project Page [BibTex]


no image
Efficient Dense Rigid-Body Motion Segmentation and Estimation in RGB-D Video

Stueckler, J., Behnke, S.

International Journal of Computer Vision (IJCV), 113(3):233-245, 2015 (article)

ev

link (url) DOI [BibTex]

link (url) DOI [BibTex]


no image
Model-Based Strategy Selection Learning

Lieder, F., Griffiths, T. L.

The 2nd Multidisciplinary Conference on Reinforcement Learning and Decision Making, 2015 (article)

Abstract
Humans possess a repertoire of decision strategies. This raises the question how we decide how to decide. Behavioral experiments suggest that the answer includes metacognitive reinforcement learning: rewards reinforce not only our behavior but also the cognitive processes that lead to it. Previous theories of strategy selection, namely SSL and RELACS, assumed that model-free reinforcement learning identifies the cognitive strategy that works best on average across all problems in the environment. Here we explore the alternative: model-based reinforcement learning about how the differential effectiveness of cognitive strategies depends on the features of individual problems. Our theory posits that people learn a predictive model of each strategy’s accuracy and execution time and choose strategies according to their predicted speed-accuracy tradeoff for the problem to be solved. We evaluate our theory against previous accounts by fitting published data on multi-attribute decision making, conducting a novel experiment, and demonstrating that our theory can account for people’s adaptive flexibility in risky choice. We find that while SSL and RELACS are sufficient to explain people’s ability to adapt to a homogeneous environment in which all decision problems are of the same type, model-based strategy selection learning can also explain people’s ability to adapt to heterogeneous environments and flexibly switch to a different decision-strategy when the situation changes.

re

link (url) Project Page [BibTex]

link (url) Project Page [BibTex]


no image
The optimism bias may support rational action

Lieder, F., Goel, S., Kwan, R., Griffiths, T. L.

NIPS 2015 Workshop on Bounded Optimality and Rational Metareasoning, 2015 (article)

re

[BibTex]

[BibTex]


no image
Kinematic and gait similarities between crawling human infants and other quadruped mammals

Righetti, L., Nylen, A., Rosander, K., Ijspeert, A.

Frontiers in Neurology, 6(17), February 2015 (article)

Abstract
Crawling on hands and knees is an early pattern of human infant locomotion, which offers an interesting way of studying quadrupedalism in one of its simplest form. We investigate how crawling human infants compare to other quadruped mammals, especially primates. We present quantitative data on both the gait and kinematics of seven 10-month-old crawling infants. Body movements were measured with an optoelectronic system giving precise data on 3-dimensional limb movements. Crawling on hands and knees is very similar to the locomotion of non-human primates in terms of the quite protracted arm at touch-down, the coordination between the spine movements in the lateral plane and the limbs, the relatively extended limbs during locomotion and the strong correlation between stance duration and speed of locomotion. However, there are important differences compared to primates, such as the choice of a lateral-sequence walking gait, which is similar to most non-primate mammals and the relatively stiff elbows during stance as opposed to the quite compliant gaits of primates. These finding raise the question of the role of both the mechanical structure of the body and neural control on the determination of these characteristics.

mg

link (url) DOI [BibTex]

link (url) DOI [BibTex]


no image
Non-equilibrium statistical mechanics of the heat bath for two Brownian particles : Internal degrees of freedom found where there shouldn’t be (Special Issue on New Challenges in Complex Systems Science)

De Bacco, C., Baldovin, F., Orlandini, E.

理工研報告特集号 : ASTE : advances in science, technology and environmentology : special issue, 11, pages: 111-113, 早稲田大学理工学術院総合研究所 (理工学研究所), March 2015 (article)

pio

link (url) [BibTex]

link (url) [BibTex]


no image
Rational use of cognitive resources: Levels of analysis between the computational and the algorithmic

Griffiths, T. L., Lieder, F., Goodman, N. D.

Topics in Cognitive Science, 7(2):217-229, Wiley, 2015 (article)

re

[BibTex]

[BibTex]


no image
Efficient single-cell poration by microsecond laser pulses

Fan, Q., Hu, W., Ohta, A. T.

Lab on a Chip, 15(2):581-588, Royal Society of Chemistry, 2015 (article)

pi

[BibTex]

[BibTex]

2006


no image
An ultrasonic standing-wave-actuated nano-positioning walking robot: piezoelectric-metal composite beam modeling

Son, K. J., Kartik, V., Wickert, J. A., Sitti, M.

Journal of vibration and control, 12(12):1293-1309, Sage Publications, 2006 (article)

pi

[BibTex]

2006


[BibTex]


no image
Die Effektivität von schriftlichen und graphischen Warnhinweisen auf Zigarettenschachteln

Petersen, L., Lieder, F.

Zeitschrift für Sozialpsychologie, 37(4):245-258, Verlag Hans Huber, 2006 (article)

Abstract
In der vorliegenden Studie wurde die Effektivität von furchterregenden Warnhinweisen bei jugendlichen Rauchern und Raucherinnen analysiert. 336 Raucher/-innen (Durchschnittsalter: 15 Jahre) wurden schriftliche oder graphische Warnhinweise auf Zigarettenpackungen präsentiert (Experimentalbedingungen; n = 96, n = 119), oder sie erhielten keine Warnhinweise (Kontrollbedingung; n = 94). Anschließend wurden die Modellfaktoren des revidierten Modells der Schutzmotivation (Arthur & Quester, 2004) erhoben. Die Ergebnisse stützen die Hypothese, dass die Faktoren «Schweregrad der Schädigung» und «Wahrscheinlichkeit der Schädigung» die Verhaltenswahrscheinlichkeit, weniger oder leichtere Zigaretten zu rauchen, vermittelt über den Mediator «Furcht» beeinflussen. Die Verhaltenswahrscheinlichkeit wurde dagegen nicht von den drei experimentellen Bedingungen beeinflusst. Auch konnten die Faktoren «Handlungswirksamkeitserwartungen» und «Selbstwirksamkeitserwartungen» nicht als Moderatoren des Zusammenhangs zwischen Furcht und Verhaltenswahrscheinlichkeit bestätigt werden.

re

DOI [BibTex]

DOI [BibTex]


no image
IEEE TRANSACTIONS ON ROBOTICS

VOLZ, RICHARD A, TARN, TJ, MACIEJEWSKI, ANTHONY A, LEE, SUKHAN, BICCHI, ANTONIO, DE LUCA, ALESSANDRO, LUH, PETER B, TAYLOR, RUSSELL H, BEKEY, GEORGE A, ARAI, HIROHIKO, others

2006 (article)

pi

[BibTex]

[BibTex]


no image
Design methodology for biomimetic propulsion of miniature swimming robots

Behkam, B., Sitti, M.

Trans.-ASME Journal of Dynamic Systems Measurement and Control, 128(1):36, ASME, 2006 (article)

pi

Project Page [BibTex]

Project Page [BibTex]


no image
Augmented reality user interface for an atomic force microscope-based nanorobotic system

Vogl, W., Ma, B. K., Sitti, M.

IEEE transactions on nanotechnology, 5(4):397-406, IEEE, 2006 (article)

pi

[BibTex]

[BibTex]


no image
Friction enhancement via micro-patterned wet elastomer adhesives on small intestinal surfaces

Kwon, J., Cheung, E., Park, S., Sitti, M.

Biomedical Materials, 1(4):216, IOP Publishing, 2006 (article)

pi

[BibTex]

[BibTex]


no image
Dynamic Hebbian learning in adaptive frequency oscillators

Righetti, L., Buchli, J., Ijspeert, A.

Physica D: Nonlinear Phenomena, 216(2):269-281, 2006 (article)

Abstract
Nonlinear oscillators are widely used in biology, physics and engineering for modeling and control. They are interesting because of their synchronization properties when coupled to other dynamical systems. In this paper, we propose a learning rule for oscillators which adapts their frequency to the frequency of any periodic or pseudo-periodic input signal. Learning is done in a dynamic way: it is part of the dynamical system and not an offline process. An interesting property of our model is that it is easily generalizable to a large class of oscillators, from phase oscillators to relaxation oscillators and strange attractors with a generic learning rule. One major feature of our learning rule is that the oscillators constructed can adapt their frequency without any signal processing or the need to specify a time window or similar free parameters. All the processing is embedded in the dynamics of the adaptive oscillator. The convergence of the learning is proved for the Hopf oscillator, then numerical experiments are carried out to explore the learning capabilities of the system. Finally, we generalize the learning rule to non-harmonic oscillators like relaxation oscillators and strange attractors.

mg

link (url) DOI [BibTex]

link (url) DOI [BibTex]


no image
Compliant and low-cost humidity nanosensors using nanoporous polymer membranes

Yang, B., Aksak, B., Lin, Q., Sitti, M.

Sensors and Actuators B: Chemical, 114(1):254-262, Elsevier, 2006 (article)

pi

[BibTex]

[BibTex]


no image
Task-based and stable telenanomanipulation in a nanoscale virtual environment

Kim, S., Sitti, M.

IEEE Transactions on automation science and engineering, 3(3):240-247, IEEE, 2006 (article)

pi

[BibTex]

[BibTex]


no image
Drawing suspended polymer micro-/nanofibers using glass micropipettes

Nain, A. S., Wong, J. C., Amon, C., Sitti, M.

Applied Physics Letters, 89(18):183105, AIP, 2006 (article)

pi

[BibTex]

[BibTex]


no image
Biologically inspired polymer microfibers with spatulate tips as repeatable fibrillar adhesives

Kim, S., Sitti, M.

Applied Physics Letters, 89(26):261911-261911, AIP, 2006 (article)

pi

Project Page [BibTex]


no image
Two-dimensional vision-based autonomous microparticle manipulation using a nanoprobe

Pawashe, C., Sitti, M.

Journal of Micromechatronics, 3(3):285-306, Brill, 2006 (article)

pi

[BibTex]

[BibTex]


no image
Engineering Entrainment and Adaptation in Limit Cycle Systems – From biological inspiration to applications in robotics

Buchli, J., Righetti, L., Ijspeert, A.

Biological Cybernetics, 95(6):645-664, December 2006 (article)

Abstract
Periodic behavior is key to life and is observed in multiple instances and at multiple time scales in our metabolism, our natural environment, and our engineered environment. A natural way of modeling or generating periodic behavior is done by using oscillators, i.e., dynamical systems that exhibit limit cycle behavior. While there is extensive literature on methods to analyze such dynamical systems, much less work has been done on methods to synthesize an oscillator to exhibit some specific desired characteristics. The goal of this article is twofold: (1) to provide a framework for characterizing and designing oscillators and (2) to review how classes of well-known oscillators can be understood and related to this framework. The basis of the framework is to characterize oscillators in terms of their fundamental temporal and spatial behavior and in terms of properties that these two behaviors can be designed to exhibit. This focus on fundamental properties is important because it allows us to systematically compare a large variety of oscillators that might at first sight appear very different from each other. We identify several specifications that are useful for design, such as frequency-locking behavior, phase-locking behavior, and specific output signal shape. We also identify two classes of design methods by which these specifications can be met, namely offline methods and online methods. By relating these specifications to our framework and by presenting several examples of how oscillators have been designed in the literature, this article provides a useful methodology and toolbox for designing oscillators for a wide range of purposes. In particular, the focus on synthesis of limit cycle dynamical systems should be useful both for engineering and for computational modeling of physical or biological phenomena.

mg

link (url) DOI [BibTex]


no image
A biomimetic climbing robot based on the gecko

Menon, C., Sitti, M.

Journal of Bionic Engineering, 3(3):115-125, 2006 (article)

pi

[BibTex]

[BibTex]


no image
Proximal probes based nanorobotic drawing of polymer micro/nanofibers

Nain, A. S., Amon, C., Sitti, M.

IEEE transactions on nanotechnology, 5(5):499-510, IEEE, 2006 (article)

pi

[BibTex]

[BibTex]